Singular Glass Hardware
My Account

Order by 1PM for Same Day Shipping - Free Pick-up in Medley

Home / Resources / Fraction calculator

Fraction calculator for feet and inches.

Tape-measure math for glass installers: add, subtract, multiply and divide feet, inches and fractions, and read the answer the way the tape shows it.

The answer shows here as you type.

Round to

Fractions

Type a measurement to turn the button on.

Every way to read it

Feet and inches
–
Inches only
–
Decimal inches
–
Decimal feet
–
Millimeters
–

Millimeters to an inch fraction

For glass thickness and metric hardware specs.

–

Tape

Nothing on the tape yet. Press = and each answer is kept here, so a run of cuts stays in front of you.

How to use the fraction calculator

Type a measurement the way you would say it on site: feet with a foot mark, inches, then the fraction. 5' 3 1/2", 63 1/2 and 5ft 3-1/2in are all the same length. A number with no mark is inches, as on a tape.

Put + or − between measurements to add or take off. Use × and ÷ with a plain number, for a count of panels or half of an opening. The answer shows as you type; press = and it goes on the tape, where a run of cuts stays in front of you. Tap an answer on the tape to start the next sum from it.

Fractions are kept exact from start to finish and rounded once, at the end, to the mark you choose: eighths, sixteenths, thirty-seconds or sixty-fourths. When an answer had to be rounded, the calculator says so, and the decimal inches beside it are the exact figure.

Sums from a frameless job

The gaps below are examples. Use the clearances on the spec sheet for your hinge, clamp or channel.

  • Door width from the opening

    Take the gaps off the opening: here a 3/16 inch hinge gap and a 3/16 inch strike gap off a 28 1/2 inch opening.

    28 1/2" − 3/16" − 3/16"= 28 1/8"
  • Split an opening into equal panels

    Divide the width by the number of panels. The calculator rounds to the mark you read on the tape and tells you it rounded.

    71 3/8" ÷ 3= 23 13/16"Rounded to 1/16"
  • Center a pull on the door

    Half the door width is the centerline. Divide by 2.

    27 5/8" ÷ 2= 13 13/16"
  • Total channel for a run

    Add the lengths as you measure them, feet and inches mixed.

    5' 3 1/2" + 2' 7/8" + 34 1/4"= 122 5/8"

Need the clearances for a part? Every spec sheet is in the resource library, and the CRL cross-reference finds our equivalent of a C.R. Laurence part number.

Inch fraction to decimal and millimeter chart

Every sixteenth of an inch, with its decimal and metric value.

FractionDecimal inchesMillimeters
1/16"0.06251.59
1/8"0.1253.17
3/16"0.18754.76
1/4"0.256.35
5/16"0.31257.94
3/8"0.3759.52
7/16"0.437511.11
1/2"0.5012.70
9/16"0.562514.29
5/8"0.62515.88
11/16"0.687517.46
3/4"0.7519.05
13/16"0.812520.64
7/8"0.87522.22
15/16"0.937523.81
1"1.0025.40

Questions about fractions and tape math

How do I add feet, inches and fractions?

Type the measurements the way you read them on the tape, with a plus between them: 5' 3 1/2" + 2' 7/8". The calculator converts everything to inches, adds the fractions exactly, and gives the answer back in feet, inches and a fraction (7' 4 3/8").

How do I type a fraction?

Type the whole inches, a space, then the fraction with a slash: 3 1/2. On a phone, tap the fraction keys under the keypad. A measurement with a dash, like 3-1/2, is read the same way.

Can I multiply or divide a measurement?

Yes, by a plain number. 24 1/2" × 3 gives the total for three equal pieces, and 71 3/8" ÷ 3 splits an opening into three panels. Multiplying two lengths together is an area, which a tape measure can't show, so the calculator asks for a plain number instead.

What does 'rounded to the nearest 1/16' mean?

Some answers fall between the marks on a tape. A third of 71 3/8" is 23.7917", which is not on any tape, so the calculator gives the nearest sixteenth (23 13/16") and says it rounded. Pick 1/32 or 1/64 under the answer when the job needs it tighter; the decimal inches are always exact.

How do I convert a decimal to a fraction of an inch?

Type the decimal as the measurement: 0.4375 reads back as 7/16", and 36.25 as 3' 1/4". The chart on this page lists every sixteenth with its decimal and millimeter value.

How do I convert millimeters to inches?

Use the millimeters box beside the calculator: 10 mm is 3/8" to the nearest sixteenth (0.3937"). There are exactly 25.4 millimeters in an inch.

Is the fraction calculator free?

Yes. It runs in your browser, needs no account, and keeps your tape of answers on your own phone or computer.